Jump to content

How to fix this?


Recommended Posts

I accidentally checked the "Same Height" option when I was working on leveling buildings in a town, and the output was not what I intended. 

 

I deleted the buildings, but I'm left with an odd height map. 

 

I tried leveling the roads but its not working. 

 

What can I do to get my map flat again?

 

weird.png

Edited by Apocalypse 31
Link to post
Share on other sites

Hi Apocalypse 31,

 I think it's not too late!

My suggestion would be as follows:

1. put a new short road ( it even could be a highway! ) over the old one and select it;

2. raise the new road with a very large shoulder width and low angle of approach;

3. look at the result without saving;

4. if you don't like it, undo and change the height(s) or/and the shoulder width/angle;

5. look at the result and if you agree save it otherwise repeat;

6. repeat this procedure with a next new short road!

7, when you're finish level all new road elements and if you agree save the result!

8. delete all new roads!

Never forget, if you agree with a result save it!

I hope, that I could help you.

Best regards

Abraxas

 

road.JPG

Edited by Abraxas
Link to post
Share on other sites
1 hour ago, Abraxas said:

Hi Apocalypse 31,

 I think it's not too late!

My suggestion would be as follows:

1. put a new short road ( it even could be a highway! ) over the old one and select it;

2. raise the new road with a very large shoulder width and low angle of approach;

3. look at the result without saving;

4. if you don't like it, undo and change the height(s) or/and the shoulder width/angle;

5. look at the result and if you agree save it otherwise repeat;

6. repeat this procedure with a next new short road!

7, when you're finish level all new road elements and if you agree save the result!

8. delete all new roads!

Never forget, if you agree with a result save it!

I hope, that I could help you.

Best regards

Abraxas

 

road.JPG

I did exactly this same trick but it wasn't flattening anything

Link to post
Share on other sites

Another trick is:

- put a former (or bigger) building on the hump. Check the position in 3D.

- lower/raise this building and use the additional border / smoothing you wish.

- Check in 3D and if you agree, save it than delete the building otherwise undo.

and so on ...

 

You can contact me by PM!

Link to post
Share on other sites
42 minutes ago, Abraxas said:

Another trick is:

- put a former (or bigger) building on the hump. Check the position in 3D.

- lower/raise this building and use the additional border / smoothing you wish.

- Check in 3D and if you agree, save it than delete the building otherwise undo.

and so on ...

 

You can contact me by PM!

That has been my method. Still a bit shoddy though. It looks very odd...but works.

Link to post
Share on other sites

I think Ssnake already covered it, but 4.2 will have a new feature to allow you to "restore" the original height data in an area. You would select Restore, and then paint with a brush over an area, and it will get reverted (can think of it like an eraser). I know in the meantime that doesn't help, but just mark the area and you should able to fix it soon.

 

(I wouldn't normally talk about a new feature, but I don't want anyone to feel like their map is ruined).

Link to post
Share on other sites
9 hours ago, Volcano said:

I think Ssnake already covered it, but 4.2 will have a new feature to allow you to "restore" the original height data in an area. You would select Restore, and then paint with a brush over an area, and it will get reverted (can think of it like an eraser). I know in the meantime that doesn't help, but just mark the area and you should able to fix it soon.

 

(I wouldn't normally talk about a new feature, but I don't want anyone to feel like their map is ruined).

Sounds good, looking forward to it.

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...